JDM Prelude 4thgen Cusco Upper Strut Brace

preludemanh22 · Post by **preludemanh22** » Fri Feb 26, 2016 6:22 pm

needs a polish as marks etc

£55 posted

mikeholl · Post by **mikeholl** » Fri Feb 26, 2016 7:13 pm

Sorry to be a pain in the ass, but I just tried to send you a PM, asking to buy the strut brace, as I could not find any other way of cotacting you. At the moment, it appears that the PM has not been sent. I freely admit that I know less than nothing about bloody computers!
If yo get this message, could you please let me know, and I will send you payment straight away, assuming you havent sold it in the meantime!!
Regards
mikeholl

preludemanh22 · Post by **preludemanh22** » Fri Feb 26, 2016 7:14 pm

U have pm

89 UKDM BA4 4WS (resto job!) · Post by **wurlycorner** » Sun Feb 28, 2016 12:17 pm

mikeholl wrote:Sorry to be a pain in the ass, but I just tried to send you a PM, asking to buy the strut brace, as I could not find any other way of cotacting you. At the moment, it appears that the PM has not been sent. I freely admit that I know less than nothing about bloody computers!
If yo get this message, could you please let me know, and I will send you payment straight away, assuming you havent sold it in the meantime!!
Regards
mikeholl

Just to re-assure... The pm will have sent. It shows in your 'outbox' until the recipient has read it, at which point, it moves to your 'sent box'

mikeholl · Post by **mikeholl** » Sun Feb 28, 2016 6:47 pm

Many thanks for words of wisdom about the workings of the website- I think I am biologically incapable of understanding the general workings of computers, and the people who write the programs for them. I think they must be extra terrestrials.

P.S. Don't suppose you have a s/h ecu to suit a 1994 JDM BB4 auto ?? When I do a 'blink' test, the check engine light comes on, and stays on. The manual tells me that this indicates a knackered ecu. If not, any idea who could repair it??
Many thanks
Mike Holloway (mikeholl)

89 UKDM BA4 4WS (resto job!) · Post by **wurlycorner** » Sun Feb 28, 2016 7:28 pm

mikeholl wrote:When I do a 'blink' test, the check engine light comes on, and stays on. The manual tells me that this indicates a knackered ecu.

Are you sure you're getting good contact across the pins on the service connector?
It is entirely possible to not get a good enough connection with a paperclip (correct sized wire is much better) or by going down the wrong side of the crimp connector inside the plug. That can give the symptoms you've described.

Prelude danny · Post by **Prelude danny** » Sat Mar 05, 2016 11:34 pm

This sold?

preludemanh22 · Post by **preludemanh22** » Sun Mar 06, 2016 10:28 am

Yes i may have a cusco front i might put up

Prelude danny · Post by **Prelude danny** » Sun Mar 06, 2016 12:50 pm

preludemanh22 wrote:Yes i may have a cusco front i might put up

Message me if you do please

mikeholl · Post by **mikeholl** » Mon Mar 14, 2016 1:03 pm

Hi David: I have lost your phone number somehow, so if you could let me know it again, that would be handy.
How did you get on over the weekend???
I have thought of some other bits I need, so if you send me your phone number, I will give you a ring.
Many thanks
Mike Holloway

Lude Generation

JDM Prelude 4thgen Cusco Upper Strut Brace

JDM Prelude 4thgen Cusco Upper Strut Brace

Re: JDM Prelude 4thgen Cusco Upper Strut Brace

Re: JDM Prelude 4thgen Cusco Upper Strut Brace

Re: JDM Prelude 4thgen Cusco Upper Strut Brace