Page 1 of 2
F22 block
Posted: Sat Dec 28, 2013 7:14 pm
by EG_H22
Hi guys
Has anyone on here used a f22 with the h22 head?
Only ask as im thinking of boosting in may and dont fancy spending out more money than needed to have the h block sleeved. And i know that the fs have iron liners which can make it possible.
If anyone can help me out
Much appreciated
Ash
Posted: Sat Dec 28, 2013 7:46 pm
by Vtecmec
I'm sure I've read somewhere there is work needed to the oilways in the block to get it to work. Also the F22 crank and associated will not be as good for higher RPM's compared to the H22.
Posted: Sat Dec 28, 2013 8:14 pm
by EG_H22
Yea ive just read that, think ill just have a h22 block sleeved instead only want to be running between 350-400 bhp nothing more lol.
Posted: Sat Dec 28, 2013 8:45 pm
by Vtecmec
only 350-400.
Posted: Sat Dec 28, 2013 9:06 pm
by EG_H22
Ha whats wrong with that, plenty of power in my h2b civic i think it will be a first too
Someone correct me if im wrong
Posted: Sat Dec 28, 2013 9:15 pm
by K30DPC
when I spoken with PAW they told me you can archhiwe this sort of output power without sleeving. Just need to buy mahle gold pistons and they will do the rest. Ofcourse they can do all job as well as providing all needed bits and piecess.
Do you already know who will sleeve your block and roughly how much they ask?
Posted: Sat Dec 28, 2013 9:25 pm
by Vtecmec
EG_H22 wrote:Ha whats wrong with that, plenty of power in my h2b civic i think it will be a first too
Nothing wrong mate, that's a lot of power to class as 'only'.
Posted: Sat Dec 28, 2013 9:25 pm
by EG_H22
Yea spoken to paw awhile back, think it worked out £1700-2300. With everything done bs removal, sleeved, bored, pistons matched up, crank balanced and poliahed rebuilt.
Same with hond-r they use a bloke that makes custom ones handling 60psi per cylinder, block same as above but for £1600. Ive managed to find someone local to me whos good mates with my mate and is willing to do mine and another block for £1000 all in.
Bargain
Posted: Sat Dec 28, 2013 9:28 pm
by EG_H22
Yes mahles can do acheive this which will also work out cheaper but have heard that they give up after awhile mates said they crumble well did on his track prelude.
But once the block is sleeved it can handle 700+ the crank itself has been tested to handle 800bhp
Posted: Sat Dec 28, 2013 9:30 pm
by K30DPC
Vtecmec wrote:Nothing wrong mate, that's a lot of power to class as 'only'.
Yes and no. I'm looking also for around this figure but with ability for about 600BHP. Especialy from bottom end must be bulletproof. Will see how about head but this is not so important atm. So I can also say I'm building the monster with only 400BHP output
Aaaahh jobby. I had to say nothing till the first dynoday
EG_H22 wrote:Ive managed to find someone local to me whos good mates with my mate and is willing to do mine and another block for £1000 all in.
My dartons are at local Post Office ATM and engine block stripped down under my staircase. If we will do 3 of them at time price may go lower. I will join this with my pleasure. But is there pistons needed with this operation? Where are you based?